Top 10 Grbl Controller Board – Single Board Computers

As an Amazon Associate I earn from qualifying purchases.

1. kuman

#ad

Kuman CNC Shield Expansion Board V3.0 +UNO R3 Board + A4988 Stepper Motor Driver with Heatsink for Arduino Kits K75 CNC Shield+UNO R3+Stepper Motor K75-CNC-UK

#ad
kuman #ad - Pwm spindle and direction pins. 4pcs a4988 stepper Motor Driver with radiator. 4-axis support. 2 x end stops for each axis 6 in total. Mcu: atmega328, usb interface: ATmega16U2. Latest cnc shield Version 3. 0 board. Runs on 12-36V DC.
Brandkuman #ad
Manufacturerkuman #ad
Height2.36 Inches
Length1.97 Inches
Weight0 Pounds
Width1.57 Inches
Part NumberK75-CNC-UK
ModelK75-CNC-UK
Warranty1 year

2. Longruner

#ad

Longruner CNC Shield Expansion Board V3.0 Board + A4988 Stepper Motor Driver with Heatsink

#ad
Longruner #ad - Latest cnc shield version 3. 4pcs a4988 stepper Motor Driver with radiator. 0 for arduinoIDE. Runs on 12-36V DC. Board for arduinoide, mcu: atmega328, USB interface: ATmega16U2. 4-axis support. 2 x end stops for each axis 6 in total. Pwm spindle and direction pins.
BrandLongruner #ad
ManufacturerLongruner #ad
Part NumberLK75-US
Model1

3. KANJJ-YU

#ad

DC 12V-36V 15A 500W Brushless Motor Controller BLDC Driver Board with Stall Over-Current Protection Supports Hallless Motors Spot Steuermodul, KANJJ-YU Control Board

#ad
KANJJ-YU #ad - 1. We will reply to your questions within 24 hours. If you have any questions, please feel free to contact us. Motor steering control wiring methods: you can switch control can also be connected to the MCU control, to GND in one direction, then in one direction 5V.

A great aftermarket part with premium quality. In order for you to get a good shopping experience here, we will provide you with high-quality pre-sales and after-sales services. Pulse speed signal: high and low output. 3. The motor speed control wiring methods: available potentiometer system speed can also be connected to the MCU control, the potentiometer middle pin is connected to VR speed port, when the potentiometer control wiring, potentiometer connected to both ends of 5V and GND terminal voltage more high speed faster. Ic can not understand the information with the customer request. 2.
BrandKANJJ-YU #ad
ManufacturerKANJJ-YU #ad
Weight0 Pounds
Part NumberKANJJ-YU

4. KANJJ-YU

#ad

KANJJ-YU Control Board, CNC USB 4 100KHz USB CNC Controller Interface Board Card Breakout

#ad
KANJJ-YU #ad - Support for 4- linkage. Fully supporting all versions. Support Emergency input. Support automatic probe tool. Maximum step-pulse frequency is 100KHz, which is suitable for the servo or stepping motor;. Small volume, it can be used after plugging in the computer. Easy to use, has a strong anti-interference ability, No need to install any USB drivers, suitable for all versions of Windows.
BrandKANJJ-YU #ad
ManufacturerKANJJ-YU #ad
Weight0 Pounds
Part NumberKANJJ-YU

5. KANJJ-YU

#ad

KANJJ-YU Control Board, 51 Microcontroller System Development Board Learning Board Robot DIY

#ad
KANJJ-YU #ad - Classic 51 minimum system. Intelligent vehicle robot diY kit, 51 Minimum System Microcontroller Development Board learning board. Support chips:. Specification: 40 pins all leads. Crystal oscillator: 11. 0592m. Stc89c52 stc12c5a60s2 stc11/10x series AT89S52 chip and pin compatible with the above chips.
BrandKANJJ-YU #ad
ManufacturerKANJJ-YU #ad
Weight0 Pounds
Part NumberKANJJ-YU

6. KANJJ-YU

#ad

KANJJ-YU Control Board, Pressure Control Module Pressure Controller Board for Water Pump Automatic Pressure Control Electronic Switches

#ad
KANJJ-YU #ad - The rated voltage is 220v to 240V AC, and maximum current is 10A. It would be a great replacement for old electronic circuit board if your switch has a problem with work. The pressure controller circuit board is suitable for water pump of power higher than 370W. This is an electronic circuit board used for water pump automatic pressure control electronic switches. Start pressure is 1. 5 bar, and pressure can be up to 10 bar.
BrandKANJJ-YU #ad
ManufacturerKANJJ-YU #ad
Weight0 Pounds
Part NumberKANJJ-YU

7. KANJJ-YU

#ad

KANJJ-YU Control Board, L9110S Dual-Channel H-Bridge Stepper Motor Dual DC Motor Driver Controller Board Module

#ad
KANJJ-YU #ad - Suitable motor scope: motor working voltage of 2. 5 v to 12 v, 08 a maximum working current. Pcb size: 2. 8 cm * 2. 1 cm super small volume, suitable assembling. If you have any questions, please feel free to contact us. Double l9110s chip motor driver chip. We will reply to your questions within 24 hours. In order for you to get a good shopping experience here, we will provide you with high-quality pre-sales and after-sales services. Power supply voltage: 2. 5v - 12V.
BrandKANJJ-YU #ad
ManufacturerKANJJ-YU #ad
Weight0 Pounds
Part NumberKANJJ-YU

8. KANJJ-YU

#ad

KANJJ-YU Control Board, 1pcs Fixed-Wing Flight gyro Balancer NX3 EVO Flight Controller Board Stabilization Controller for 3D 2D Flight

#ad
KANJJ-YU #ad - 1 piece nx3 evo flight Controller Board. Fixed-wing flight gyro balancer nx3 evo flight controller NX3 EVO Flight Stabilization Control for 3D 2D Flight RC Airplane. Automatic level offset, self-balance. Single/separate Dual ailerons recognition capability. Including emergency mode, One-key auto safety.
BrandKANJJ-YU #ad
ManufacturerKANJJ-YU #ad
Weight0 Pounds
Part NumberKANJJ-YU

9. ELEGOO

#ad

RoHS Compliant, ELEGOO UNO R3 Board ATmega328P ATMEGA16U2 with USB Cable Compatible with Arduino IDE Projects

#ad
ELEGOO #ad - New improvement: clear prints on the female header connector, more precise and easier to use the wire. We have always cared about the customer experience and improve the product function details. Faster transfer rates and more memory. Control using atmel atmega328p chipthe same with Arduino UNO R3. 100% compatible with the Arduino IDE and RoHS Compliant. The elegoo uno r3 board now uses an atmega16u2 instead of the ATMega8U2 chip.
BrandELEGOO #ad
ManufacturerELEGOO #ad
Height0.39 Inches
Length3.15 Inches
Weight0.14 Pounds
Width2.36 Inches
Part NumberEL-CB-001
ModelEL-CB-001

10. ELEGOO

#ad

ELEGOO MEGA 2560 R3 Board ATmega2560 ATMEGA16U2 + USB Cable Compatible with Arduino IDE, RoHS Compliant

#ad
ELEGOO #ad - 5mm dc barrel jack. The mega is 100% compatible with arduino ide and most of the shields are designed for the Arduino mega2560 R3,RoHS Compliant. 5 * 2. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started. 1mm dc barrel jack compatible with 5. The chip is atmega2560-16au and Atmega16u2, same with the official version. 5 * 2. Stronger reset circuit. Improved and expert version: 1. Use 5. 0 pinout: added sda and sCL pins that are near to the AREF pin.
BrandELEGOO #ad
ManufacturerElegoo #ad
Height0.71 Inches
Length5.04 Inches
Weight0.14 Pounds
Width3.35 Inches
Part NumberEL-CB-002
ModelLYSB01H4ZDYCE-ELECTRNCS