Top 10 UCTRONICS for Raspberry Pi PoE – Single Board Computers

As an Amazon Associate I earn from qualifying purchases.

1. UCTRONICS

#ad

Mini Power Over Ethernet Expansion Board for Raspberry Pi 4 B 3 B+, UCTRONICS PoE HAT for Raspberry Pi 4

#ad
UCTRONICS #ad - Well-ventilated environment recommended: it’s normal to become hot when the HAT operating. For pi 4 and 3 b+: this poe hat can be used to deliver clean and reliable power to the raspberry pi 3 model B+ and raspberry pi 4 model B not included.

Please make sure the adequate air circulation to help it dissipate heat to ensure stable operation. Smaller size: nearly half the official size, save more space for your other hardware, can be held in the most case for Raspberry Pi. Note: pse power supply equipment is needed to supply PoE signal to the Raspberry Pi, such as a PoE switch or injector. If used with pi 4, you can search ASIN B07WMNXB4V to get the case with the fan. Output power: dc 5v 2. 5a max; total power budget: 12. 5w; ieee 802. 3af Compliant.
BrandUCTRONICS #ad
ManufacturerUCTRONICS #ad
Height0.94 Inches
Length3.1 Inches
Width2.2 Inches
Part NumberU6109

2. UCTRONICS

#ad

UCTRONICS PoE HAT for Raspberry Pi 4, with Cooling Fan, 802.3at Power Over Ethernet Expansion Board for Raspberry Pi 4 B 3 B+

#ad
UCTRONICS #ad - Higher output power: dc 5v 3a max / 12v 2a max via on-board terminal block; Total Power Budget: 25W. To fit in most pi cases that have room for a hat board in general, please search for ASIN B08TGXVCCM, which was removed the 12V power terminal block.

Over-temperature protection: the 25mm×25mm brushless cooling fan will turn automatically when the temperature of the processor is high. This poe hat can be used with raspberry pi 3 model B+ and raspberry pi 4 model B not included. Note: pse power supply equipment is needed to supply PoE signal to the Raspberry Pi, such as a PoE switch or injector.
BrandUCTRONICS #ad
ManufacturerUCTRONICS #ad
Part NumberUCT_U6102

3. UCTRONICS

#ad

UCTRONICS for Raspberry Pi PoE Splitter 5V 2-Pack, Active PoE to Micro USB Adapter, for Tablets, and More, IEEE 802.3af Compliant, Dropcam and Raspberry Pi 2/3

#ad
UCTRONICS #ad - That means it adds plug-and-play poe support to raspberry pi models even they are not 3 B+ and cannot accommodate a Raspberry Pi PoE HAT. 2: for one pack, check b01mdluse7; for gigabit poe switch or a raspberry Pi 3 B+, check B01MPWW2UV. It makes full use of poe switches because the other end of the PoE port could be any micro USB devices instead of a 48V PoE network device.

What’s special about it - poe to micro usb. What is poe - poe enables you to deliver power and data with a single ethernet cable, and thus fewer wall plugs are needed and fewer cables are messed. These are not included in our package. 3: the split ethernet cable does not carry power, check gigabit poE splitter B07CNKX14C; For 12V barrel port, but you can add a USB Ethernet adapter to it if your device takes network from USB. What is it - a 5v uctronics poe splitter to split the poe signal into micro usb power supply and ethernet in rj45, Amazon Cloud Cam, arlo 2 pro, Amazon Ethernet Adapter for Fire TV, ASUS Tinker Board, nano pi, chromecast, so that non-PoE devices can be powered over Ethernet.

What else is needed - you need an ieee 802. 3af compliant poe switch or injector to serve as the PSE Power Source Equipment, an Ethernet cable with the proper length you need, and devices powered via micro USB. It also helps you extend powerline to where there are no AC outlets nearby but your Ethernet cable can reach, up to 300 feet away from the power source. Reportedly used on micro usb devices like Raspberry Pi, Echo Dot 2nd Gen, Wyze Cam v2, and so on.
BrandUCTRONICS #ad
ManufacturerUCTRONICS #ad
Height0.94 Inches
Length6.69 Inches
Width4.72 Inches

4. UCTRONICS

#ad

UCTRONICS for Raspberry Pi 4 PoE HAT with Cooling Fan, Mini Power Over Ethernet Expansion Board for Raspberry Pi 4 B, 3 B+ and Rackmount

#ad
UCTRONICS #ad - Intelligent temperature control: the 25mm×25mm brushless cooling fan will turn automatically when the temperature of the processor is high. Output power: dc 5v 2.

5a max; total power budget: 12. 5w; ieee 802. 3af Compliant. 2. Pse power supply equipment is needed to supply poe signal to the Raspberry Pi, such as a PoE switch or injector. Smaller size: save more space than the official HAT, no hassle to assemble with the Raspberry Pi and mount on the rackmount. This poe hat can be used with raspberry pi 3 model B+ and raspberry pi 4 model B Raspberry Pi boards are not included. Please make sure the adequate air circulation to help it dissipate heat to ensure stable operation. Note: 1.
BrandUCTRONICS #ad
ManufacturerUCTRONICS #ad
Part NumberU611001

5. UCTRONICS

#ad

IEEE 802.3af Compliant, Work with Echo Dot, UCTRONICS PoE Splitter Gigabit 5V, Micro USB Power and Ethernet to Raspberry Pi 3B+, Most Micro USB Security Camera and Tablet

#ad
UCTRONICS #ad - Support raspberry Pi 3b+ and previous models. Replace power supply - remove the need for a separate power supply if the Ethernet cable is a must-have for your micro USB devices.

Note: an 802. 3af compliant poE injector/switch is required to use this device not included. Save your time - plug and play compatibility and quick seller response. Compatible with Raspberry Pi case with fan or add-on screen. Extend powerline - deliver power to micro USB devices without nearby AC outlets and upgrade them to PoE Power over Ethernet from up to 400 feet. 5v/2. 4a & 1000mbps - power micro-usb devices via an Ethernet cable, along with gigabit data transfer which you can put aside if you only need power. Poe hat alternative - use no gpio pins.
BrandUCTRONICS #ad
ManufacturerUCTRONICS #ad
Height1.97 Inches
Length3.15 Inches
Width0.59 Inches
Part NumberU515902
ModelU515902

6. UCTRONICS

#ad

Active PoE to USB-C Adapter, Google WiFi, IEEE 802.3af Compliant for Raspberry Pi 4, and More, Security Cameras, UCTRONICS PoE Splitter USB-C 5V

#ad
UCTRONICS #ad - Note – 1. 3. What is it - a uctronics poe splitter to split the poe signal into 5V USB-C power supply and gigabit Ethernet in RJ45 so that non-PoE devices can be powered over Ethernet. What else needed - you need an ieee 802.

3af compliant poe switch or injector to serve as the PSE Power Source Equipment and an Ethernet cable with PoE signal to feed the splitter. 2. 4. What is poe – deliver power and data with a single ethernet cable for fewer wall plugs and messed cables. Just put the split Ethernet aside if you don’t need the data. This splitter does not support pd or qc fast charging protocols. Check b07v35dh5f for power-hungry applications.

The split ethernet cable does not carry power anymore. Why poe to usb-c – a cost-effective way to add plug-and-play poe support to 5V USB-C powered devices and make full use of PoE switches, or for a Raspberry Pi 4 setup where a PoE HAT is not applicable. This splitter provides a maximum output of 2. 4a with its 802. 3af compliance. Extend powerline to where no AC outlets are nearby, up to 300 feet away from the power source.
BrandUCTRONICS #ad
ManufacturerUCTRONICS #ad
Part NumberU6115

7. UCTRONICS

#ad

And More, Google Mini, UCTRONICS for Raspberry Pi Zero Ethernet and Power, IEEE 802.3af Compliant, Micro USB Ethernet/PoE Adapter for Fire TV Stick, Chromecast

#ad
UCTRONICS #ad - Note: 1. What else needed - you need an ieee 802. 3af compliant poe switch or injector for the PoE mode, or an extra Micro-USB power supply for plain Ethernet combining. How does it work – by converting poe power over Ethernet signal, or combining plain Ethernet and Micro-USB power supply, into Power&Ethernet over USB.

Make sure the poe input is connected to a functioning IEEE802. 3af compliant poe switch that has internet connectivity and power over Ethernet on PoE mode. For raspberry pi zero, plug into the micro usb port marked “usb” instead of “pWR.

2. Extend powerline to where no AC outlets are nearby, up to 300 feet away from the power source. What is it – an adapter that helps you deliver both power supply and solid wired network connection to a single Micro-USB port. What is poe – deliver power and data with a single ethernet cable for fewer wall plugs and messed cables.
BrandUCTRONICS #ad
ManufacturerUCTRONICS #ad

8. UCTRONICS

#ad

UCTRONICS IEEE 802.3af Micro USB Active PoE Splitter Power Over Ethernet 48V to 5V 2.4A for Tablets, Dropcam or Raspberry Pi 48V to 5V 2.4A

#ad
UCTRONICS #ad - Power output port: 5v 2. 4a micro usb Power Plug. Support ieee 8203af poe switch, 48v injector. 2-pack: b07qprvM51. Suitable for android tablets, dropcam, raspberry Pi – Micro USB. 12 watt micro usb power over ethernet poe up to remote 328-492ft 100-150m via Ethernet cable, 802. 3af poe switch or 48v injector is needed. Compatible with 44-57V DC voltage, overvoltage protection. For gigabit poe switches users, 48v unsolicited Power Over Ethernet PoE Switch or Ethernet PoE Adapter, gigabit splitter U515902 is recommended.
BrandUCTRONICS #ad
ManufacturerUCTRONICS #ad
Height1.97 Inches
Length3.15 Inches
Width0.59 Inches
Part NumberUCT_U5159
ModelU5159

9. Raspberry Pi

#ad

Official Raspberry Pi Power Over Ethernet PoE HAT for Raspberry Pi 3 B+ and 802.3af PoE Network

#ad
Raspberry Pi #ad - May be used to power your raspberry pi 3 B+ with an Ethernet cable on a PoE enabled network, eliminating the need for a separate power supply. Class 2 poe device: 36-57v input, 5v/2. 5a output. 802. 3af compliant PoE. This is the updated version, which addresses the current limiting issue found in the original release. This is the 2018 official raspberry pi power over ethernet PoE HAT for the Raspberry Pi 3 Model B+. Smps: fully isolated Switched-Mode Power Supply with fan for cooling.
BrandRaspberry Pi #ad
ManufacturerRaspberry Pi #ad
Height0.98 Inches
Length2.95 Inches
Weight0.13 Kilograms
Width3.15 Inches
Part Numberrb-poehead2
Modelrb-poehead2

10. LoveRPi

#ad

Isolated 3KV, LoveRPi Power-Over-Ethernet PoE HAT for Raspberry Pi 4 Model B and Raspberry Pi 3 Model B+ Professional

#ad
LoveRPi #ad - Poe switch and raspberry Pi 4 Model B sold separately. Built for cluster nodes: simplify cable management and expand your on-premise cloud with POE! Power five, ten, twenty Raspberry Pi 4 Model B boards through a single POE switch. The professional model features galvanic isolation for applications with non-IEEE 802.

3 compliant switches and power injectors that do not provide PSE side isolation. Poe power output must be within the budget of the switch when powering multiple boards. This poe hat was designed to exceed the power delivery standards set by the official Raspberry Pi PoE HAT and other products available on the market. Galvanically isolated power over ethernet up to 3kv: designed for ieee 802. 3af, ieee 802. 3at, and passive dc 48V network switches and power sourcing equipment PSE. Ventilated case with cooling fan highly recommended: Do not use this product in an enclosed case without active air circulation.

Airflow around the hat and Raspberry Pi 4 Model B must be adequate to ensure performance and stable operation. Ultimate power over ethernet hat for raspberry pi 4: deliver clean and reliable power to the latest Pi 4! Power-over-Ethernet is both simple, power efficient, and cost effective compared to having multiple power adapters. Backwards compatible: supports the latest Raspberry Pi 4 as well as the Raspberry Pi 3 Model B+.
BrandLoveRPi #ad
ManufacturerLoveRPi #ad
Part NumberLRP-RPIHAT-POE-RPI4