Top 9 Load Cell 5kg – Electronics

As an Amazon Associate I earn from qualifying purchases.

1. DollaTek

#ad

DollaTek 5kg Small Scale Load Cell Weighing Pressure Sensor with A/D HX711AD Adapter

#ad
DollaTek #ad - In particular, be sure not to directly press the white rubber part to avoid damage to the sensor. Wiring method: red: power +, green: output signal +, black: power -, white: output signal. One end of the sensor is fixed by a screw hole, and the other end is left floating, and gravity is applied in the direction indicated by the label. Four leads, easy to use, plus 5-10V drive voltage, direct output as voltage signal due to force changes. Small range weighing pressure sensor with HX711AD module Weighing module.
BrandDollaTek #ad
ManufacturerDollaTek #ad

2. CHENBO

#ad

CHENBO Load Cell Weight Sensor 1kg + HX711 Weight Weighing A/d Module Pressure Sensor

#ad
CHENBO #ad - Accurate measures forces from 0-5kg 0-11 lb. Sturdy aluminum alloy construction with strain gauges pre-attached with strain relieved wires. On-chip active low noise pGA with selectable gain of 32, 64 and 128. Input end: red+, black-; output end: green+, White-; Excitation Voltage: 5-10V DC. Simple digital control and serial interface: pin-driven controls, no programming needed. Selectable 10sps or 80SPS output data rate.
BrandCHENBO #ad
ManufacturerCHENBO #ad
Part NumberNCOREDSHJKJKF7938
ModelNCOREDSHKF7938

3. KOOKYE

#ad

Load Cell Amplifier ADC Weight Sensor for Arduino Scale, KOOKYE 5kg Load Cell and HX711 Combo Pack Kit

#ad
KOOKYE #ad - Hx711 - this top of the line load cell amplifier mounted on a breakout board pairs perfectly with the load cell to provide fast, accurate force measurements.

It measures small changes in the resistance of the strain gauges mounted to the load cell and passes these values directly to any micro controller like an Arduino or Raspberry Pi. Accurately measures forces from 0-5kg 0-11 lb. One both holes tapped M4 thread, 12. 7 mm wide, 80 mm long 05 in x 05 in x 3. 15 in. 4 mounting holes, the other side both holes tapped M5 thread. Load cell - sturdy aluminum alloy construction with strain gauges pre-attached with strain relieved wires. Load cell specs - 22 cm 8. 5 in wire leads pre-attached. Dimensions 12. 7 mm high, 15 mm spacing on each side.
BrandKOOKYE #ad
ManufacturerKOOKYE #ad
Part Number2020001500
Model2020001200

4. PROAIM

#ad

Proaim Megagrip Car/Vehicle Camera Mount with Flight Case CM-MGGP-01

#ad
PROAIM #ad - Professional gripper suction Mount – Provides Ultimate Experience In Vehicular Stabilization. Spring-balanced suction cups – ensures much more reliable hold on surface; Tool-less Operation; Easy, Secure Set-up - Saves lot of Production Time.

Flexible ball levelling head – quickly adjusts your camera in desired position; Extendable Rods – gives freedom to mount in any configuration. High-grade aluminum construction - ensures ultimate Stability; Running & Still Load Capacity: 5-15kg/11-33lb, Maximum speed - 200km/h. Includes flight case; 100% Customer Satisfaction Guarantee, Buy with Confidence.
BrandPROAIM #ad
ManufacturerProaim #ad
Height13.39 Inches
Length29.92 Inches
Weight59.52 Pounds
Width22.83 Inches
Part NumberCM-MGGP-01
ModelCM-MGGP-01
Warranty1 year

5. railing

#ad

Load up to 10lbs/5kg, Portable Camera Slider Adjustable Aluminum Alloy Rail, Compatible with Android Cell Phones and Mirrorless Cameras

#ad
railing #ad - There are 1/4 and 3/8 screw holes on both sides and middle of the slide rail, which can be used with other equipment such as tripod to make the slide rail more powerful.

The new non-slip foot pad, adjustable design, 360-degree spherical design, suitable for various scenes, retractable quickly and support more stable. The outer side of the slider is equipped with manual adjustment damping, and the elasticity can be adjusted at will. 50cm portable size, lightweight, coming with a scratch-resistant carrying bag, it is perfect to be packed in your backpack or luggage for travelling anywhere. The looser the adjustment, the smoother the sliding. The tracking slider can be used on any surface with removable and adjustable legs and non-skid rubber feet and is convenient for fine adjustment with bubble level.
Brandrailing #ad
ManufacturerA3VQTV4V10MV86 #ad
Part NumberA3VQTV4V10MV86

6. KINGJOY

#ad

KINGJOY 75" Camera Tripod for Canon Nikon Lightweight Aluminum DSLR Camera Stand with Carry Bag Universal Phone Mount and Wireless Remote Max Load 5kg

#ad
KINGJOY #ad - The high-quality aluminum alloy feet and the Upgraded trapezoidal flap lock allow you to smoothly adjust the height from 19 inches to 75 inches in a few seconds. Come with a wireless remote, taking selfies, pairs with your mobile so that you can take photos/video from 30ft/10m away.

This professional tripod for camera provides ultra stability and steadiness for various terrain and helps photographers take stunning photos. This tripod with a carry bag. The mount comes with soft protective rubber for extended durability and securing your phone/tablet to avoid it from scratching or damage. Contact us freely if any issue occurs, 1 x Bluetooth remote control, we will offer proper solution for you at the first time.

The collapsed size of Kingjoy 75 inch camera tripod is only 19. 2 inch, max load is 5 kg/11 Lb and weight is only 2. 9 lb. Tripod for all cameras with a 1/4" quick release plates compatible with all dslr, nikon d3200 d3400 d3500 d5200 d5600 d7500 z50 etc. The best camera phone tripod stand? Here you get. Upgraded double sponge pad design. 100% satisfaction & excellent service with a zipper carry bag for easy carrying and secure storage the tripod.
BrandKINGJOY #ad
ManufacturerKINGJOY #ad
Part Number990L

7. Jeanoko

#ad

DYX-306 Load Cell Sensor Measuring Weight Single Point Pressure Sensor Detector Monitor DC5-12V for Force Measurement in Industrial Systems5KG

#ad
Jeanoko #ad - With excellent electrical conductivity, thermal conductivity and corrosion resistance. Parameters - sensitivity: 2. 0±005mv/v; non-linearity: ≤002%f·s; lag: ≤003%f·s; repeatability: ≤002%f·s; creep: ≤003%f·s/30minl; zero output: ≤1%F·S; Zero Temperature Coefficient: ±003%f·s/10℃; sensitivity Temperature Coefficient: ±003%f·s/10℃.

Using with confidence - possess excellent electrical conductivity, widely used in industry, dust-proof sealing, thermal conductivity and corrosion resistance, strong stability, and its usage is second only to steel. Wide applications - used for force measurement in industrial systems, mainly for industrial automation measurement and control system for measuring tension and pressure and other kinds of weighing and force measurement.

Possess low structure height - possess low structure height, can measure tension/pressure. And widely used in industry, saving space, and its usage is second only to steel. Made of aluminum alloy - the density of aluminum alloy is low and the strength is relatively high, which is close to or exceeds that of good?quality steel. Come with high accuracy, and wide measuring range. Has good plasticity and can be processed into various profiles.
BrandJeanoko #ad
ManufacturerJeanoko #ad
Height0.39 Inches
Length0.39 Inches
Width0.39 Inches
Part NumberJeanoko0zyi8mraf6755-12

8. Victiv

#ad

2 Quick Release Mounts and Tablet & Phone Mount, 73 inch Tripod for Camera 15 lbs Loads with Fluid Head, Tripod

#ad
Victiv #ad - Designed to get extremely tall, this camera tripod is up to 73 inches and features a simple lever lock for much easier to unlock and lock. Strong, architectural, and landscape photography, where you need your scene to be as sharp as possible, durable but lightweight -- Enhancing its portability, it weighs just 3.

2 lb and is made of 90% aluminum and 10% durable plastic for easy-to-transport feature. Height winner -- a center column raises or lowers at the turn of a hand crank to let you fine-tune a height without adjusting the tripod legs. Typically for real estate, interior, often in low light conditions. Functional accessories -- to make the victiv phone & tablet tripod even better and more complete, it does come with two quick release plates, universal phone & tablet tripod mount, carrying bag for easy transportation and 2 years warranty guarantee for worry-free. The included middle brace holds the legs in position while also attributing rigidity and support to the tripod.

Versatility fluid head -- a built-in fluid effect video head pans a full 360°, tilts up and down, and features independent pan and tilt locks for fixed-position shots. Half price pro performance -- designed for digital cameras, ipad, mobile phones, small camcorders, the lightweight and professional tripod system supports devices weighing up to 15 lbs. These provide extra flexibility and more precise framing when taking selfies or group photos that you want to be a part of. It is suitable for use for event and wedding coverage.
BrandVictiv #ad
ManufacturerVictiv #ad
Weight3.3 Pounds
Part Number01
Model01
Warranty1 year warranty

9. HCDC

#ad

HCDC RPi GPIO Status LED & Terminal Block Breakout Board HAT for Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B

#ad
HCDC #ad - 2 x 20 pins expansion pin header, strip length 5mm, height 8mm/032". The item has been soldered and assembled. Gpio output or input level high led on, 3. 3v red, and the logic level of the gpio can be observed very quickly and intuitively.

Support for raspberry pi a+ 3A+ B+ 2B 3B 3B+ 4B. 5v blue, gPIOs green. Packing list: 1x terminal block breakout module, 4x m2. 5x6mm nylon standoffs, 4x M2. 5x16mm nylon standoffs, 4x M2. 5 nylon nutsnote: the item not include Raspberry Pi Board. Gpio status led and power 5v / 3. 3v indication. Terminal block pitch 3.

5mm/0138", screw m2 steel, wire size range 26aWG to 16AWG, pin header and cage copper. The position of the led is in a one-to-one correspondence with the position of the Raspberry Pi 2x20pin connector, so you don't have to worry about it affecting the read and write status of GPIO. The driving current of each LED is only 01ma, output or input level low LED off.
BrandHCDC #ad
ManufacturerXiken Electronic Technology Co., Ltd. #ad
Part NumberHD040